ASSEMBLY INSTRUCTIONS
POSITION
- Choose a position on a suitable clean, flat surfaced wall, which can provide suitable mounting.
- Do not place near sources of heat or cold, such as a heater or air conditioner. The product operates best in a room temperature between 68° F/20° C and 75° F/24° C.
- Keep the cable away from heated surfaces.
- For best performance, we recommend you keep the product away from: sunlight to prevent fading, drafts and cold place to prevent slow operation and freezing, hot places to prevent overheating.
- For indoor use only.
SETUP
This product comes with 8 components:
- Base
- Bottle
- Long arm piece
- M4 Screw x 1
- M2.5 Allen key x 1
- Switching power adapter
- UK interchangeable plug
- EU interchangeable plug
MOUNTING INSTRUCTIONS:
NOTE: Different wall materials require different types of fittings. Always choose screws and plugs that are suited to the material. If in doubt please use a professional installer
- Place the wall mounting plate on a suitable flat surfaced wall. Make sure that the plate can be placed flat against the wall before mounting. Ensure the plate is vertically mounted.
- Secure in place with 4 suitable screws through the holes on the back plate. (fixing screws not supplied)
- Ensure the cable is fed correctly through the wall cover as shown. Slot the base & wall cover assembly on to the wall mounting plate by hooking the lugs in to the three keyholes.
- Check the assembly is hooked on to the wall mounting plate, then secure to the plate by pressing in and turning the screw in the stem of the product using the larger M4 Allen key provided. Ensure the screw is tightened enough so that the assembly cannot be lifted off the wall plate.
- Once secure, place the long arm piece on top of the bottle and firmly push in place. Align the Mathmos logo to be facing forward. Carefully place the bottle with the arm piece into the lower cup and line up with the screw hole in the rear of the lower cup.
- Insert the screw provided and tighten with the smaller M2.5 Allen key provided.
- Slide the correct plug inset (EU or UK) on to the switching power adapter until it clicks.
- Plug the switching adaptor provided in to the cable DC socket. Plug the product in and turn it on.
WARM UP
Between 1-3 hours depending on the surrounding temperature. Stalagmite shapes may form during the warm up process, these will then melt and the lava will begin to flow. It is normal for the glass to have small air bubbles and moulding scars.
OPERATION
Your Mathmos product will operate best after it has been used four or five times. For the first few times you may see small air bubbles in the lava. Please note the heating time will decrease after several uses.
Please do not leave the product on for more than six hours a day or allow it to overheat; this will prolong the life of the product. Overheating will shorten the life of the product; if it is overheating there will be either only one large bubble at the top of bottle or a lot of very small bubbles.
Never move or shake the lamp when it is in use or still warm, as this causes irreparable clouding.
REPLACEMENTS
When your product has ended its like it will begin to go cloudy, the colours may fade and it will not move as well as it once did. This will happen after approximately 2000 hours in operation. Whether your product has ended its life or when you wish to have an alternative colour combination, visit our website at www.mathmos.com for more information on a replacement bottle or full product. Please note we do not refill bottles. Please on no account open the secure cap and add liquids.
If the bulb blows, please replace it with one of the same type and wattage. Only fit the correct bulb, as stated in the label in the base. Visit our website at www.mathmos.com for more information on replacement bulbs.
IMPORTANT! Always allow the product to cool down completely prior to handling. Do not attempt to move the product until fully cooled.
Once your product has completely cooled, use the Allen key provided to unscrew and remove the back screw out (keep these components safe). Carefully, holding the bottle and arm piece, lift and remove the bottle and arm piece from the base. Carefully take the arm piece off the bottle and place it onto the bottle you would like to use. Now refer to ‘set up’ for instructions on how to assemble.
POWER SUPPLY
The product is supplied with a switching adaptor (Input 100-240v ~ 50/60 Hz, Output 12V 2.5A). This product’s external flexible cable cannot be replaced. If the cable is damaged in anyway the product should be destroyed.
SAFETY INSTRUCTIONS
- This product carries the statutory guarantee of the country of purchase and meets all the applicable standards requirements.
- Use this product only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
- Do not leave this product unattended when not assembled. Do not lean or push down on the product once it is mounted on the wall.
- Do not use any other means to heat up the bottle other than the bulb provided nor attempt to cool it down artificially.
- Do not operate the product for more than 6 hours a day.
- The liquids in the product are not dangerous and can be disposed of normally (for details see our online FAQ’s at www.mathmos.com). If the liquid is swallowed by mistake, drink plenty of water. If any symptoms appear, please visit a doctor.
- Never use this product if the bottle has been dropped as this will create weakness; obtain a replacement bottle from Mathmos and dispose of the old one in a safe and environmentally friendly manner.
- If the contents of the bottle are spilt, please dispose of as much liquid and lava as you can remove, then use recommended cleaning methods for removing the coloured water and wax on whatever surfaces you have.
To reduce the risk of burns, electric shock, or injury to persons:
- Unplug from outlet before putting on or taking off parts or before cleaning.
- Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or if it has been submerged in water.
- The external flexible cable of this product cannot be replaced. If the cable is damaged, the product shall be discarded.
- To disconnect, turn the switch to the off position, then remove plug from outlet.
- Never touch the bulb if the product is switched on or if it has just been switched off to avoid burning. To replace a defective bulb, unplug the product and let it cool down sufficiently.
The product manufacturer cannot be made liable for damage or injury caused by improper handling, installation or use of its products.